Type 94 pick-up laser cladding

Non-sparking cladding picks, in order to improve the service life of the picks and enhance the safety of underground mining, laser cladding technology is used to weld non-sparking tungsten carbide powder on the pick head, and the hardness of the cladding layer is ≥60HRC. The tooth head improves the wear resistance at the same time, controls the spark, effectively improves the safety of the mining site, and the non-spark cladding cutter is a general trend of development and promotion. The specific technical requirements are: 1. Appearance quality: The appearance of the tooth body is smooth and flat, without defects such as cracks, folds and dents visible to the naked eye, and the surface of the tooth body is protected against rust; 2. Surface hardness: after the tooth body is heat treated, the surface hardness of the tooth head surface is ≥40HRC, and the surface hardness of the tooth body is 38-42HRC. 3. Impact toughness: impact toughness after tooth heat treatment ≥49J/cm2 4. Shear strength of brazed joint: Shear strength of brazed joint of tooth body and hard alloy ≥180MPa 5, weld fullness: the solder fill level in the weld is not less than 80%; 6, the hardness of the cladding layer of the cladding layer ≥ 60HRC 7. Crack inspection: There shall be no cracks in the weld zone and the joint surface of the solder and the base metal, and the cemented carbide head shall not have cracks;

View more
55# knife teeth

55# cutter: The effect of cutting is better than that of ordinary pick cutting, the effect of spray dust removal is good, the cutter pick does not consume the tooth sleeve, which can reduce the cost of use, improve work efficiency and low maintenance time.

View more
Type 84 pick (wear type)

The universal wear-resistant pick, on the basis of the universal type, is covered with a layer of wear-resistant layer on the tooth head, which is more wear-resistant than the general-purpose pick. More time aging. Tooth impact toughness ≥ 49cm2; brazed joint shear strength ≥ 180MPa; tooth hardness ≥ 38HRC

View more
84 type picking powder surfacing

Non-sparking cladding picks, in order to improve the service life of the picks and enhance the safety of underground mining, laser cladding technology is used to weld non-sparking tungsten carbide powder on the pick head, and the hardness of the cladding layer is ≥60HRC. The tooth head improves the wear resistance at the same time, controls the spark, effectively improves the safety of the mining site, and the non-spark cladding cutter is a general trend of development and promotion. The specific technical requirements are: 1. Appearance quality: The appearance of the tooth body is smooth and flat, without defects such as cracks, folds and dents visible to the naked eye, and the surface of the tooth body is protected against rust; 2. Surface hardness: after the tooth body is heat treated, the surface hardness of the tooth head surface is ≥40HRC, and the surface hardness of the tooth body is 38-42HRC. 3. Impact toughness: impact toughness after tooth heat treatment ≥49J/cm2 4. Shear strength of brazed joint: Shear strength of brazed joint of tooth body and hard alloy ≥180MPa 5, weld fullness: the solder fill level in the weld is not less than 80%; 6, the hardness of the cladding layer of the cladding layer ≥ 60HRC 7. Crack inspection: There shall be no cracks in the weld zone and the joint surface of the solder and the base metal, and the cemented carbide head shall not have cracks;

View more
84 grooved pick

The rotary groove picks are mainly designed for hard rock. 1. The shape is specially designed. In order to prolong the service life, no eccentric wear is generated during use, and the tooth head is designed as a spiral groove shape, which is added during use. The self-rotating function achieves uniform wear of the alloy and the periphery of the tooth head, and improves the service life. 2. At the end of the tooth head, the wear resistance of the tooth body is enhanced, and the non-sparking alloy powder is melted, and the hardness is ≥60HRC, which greatly improves the safety and mining efficiency of the underground mining. 3. The weight of the alloy head is obviously larger than that of the general pick, which enhances the impact strength of the alloy, and the bigger and more durable. 4. The alloy adopts the grade of super coarse grain, which improves the heat dissipation performance of the alloy head. On the basis of high wear resistance, it also has high toughness. 5. In order to ensure the welding strength and shear strength of the alloy head, the industry's advanced pick brazing heat treatment line equipment uses imported flux and solder. The specific technical requirements are: 1. Appearance quality: The appearance of the tooth body is smooth and flat, without defects such as cracks, folds and dents visible to the naked eye, and the surface of the tooth body is protected against rust; 2. Surface hardness: after the tooth body is heat treated, the surface hardness of the tooth head surface is ≥40HRC, and the surface hardness of the tooth body is 38-42HRC. 3. Impact toughness: impact toughness after tooth heat treatment ≥49J/cm2 4. Shear strength of brazed joint: Shear strength of brazed joint of tooth body and hard alloy ≥180MPa 5, weld fullness: the weld fullness of the weld is not less than 80%; 6, the hardness of the cladding: the hardness of the cladding layer ≥ 60HRC 7. Crack inspection: There shall be no cracks in the weld zone and the joint surface of the solder and the base metal, and the cemented carbide head shall not have cracks.

View more
久草国产视偷拍